DIY Pallet Garden Front

Make your own Pallet Garden

Have you got a spare pallet knocking around? They are easy to get hold of if not…. and what a gorgeous project this is! Just follow the steps below to create your own repurposed Pallet Garden. Thank You so much to the ingenious Hannah at The Chimney House for the inspiration. You can check out her fantastic Blog using the link for Meeting, Making and Munching!

DIY Pallet Garden Front
DIY Pallet Garden Front

1- Find a pallet. They’re all slightly different. Look at their bottoms or underneath. This is the side you will have facing you to plant into. I chose ones with just four slats as I wanted a bit more space between each slat for the plants. Also, if you’re having a few side by side, check the ‘colours’ and fading of the wood match. I found one was very grey and one was a warm yellow, so searched though our pile until I had two similar in colour.

2- Turn them, so the underneath is facing you and slats are horizontal. Now you have two choices! You can either back the whole lot, fill with compost whilst lying on the floor, plant whilst it’s flat, then stand and secure to wall OR stand against wall (preferably a garden wall. If it’s against the wall of your house you must leave a gap and put a watertight membrane against the back of the pallet you so don’t end up getting damp! ) secure to wall, put in little compost holders and fill with plants.

DIY Pallet Garden
DIY Pallet Garden

A)
If you chose the backing and planting whilst flat, here’s what to do next…

Back (as in, cover the top/front, since the underneath is now your front) the pallet with a strong weed-stop membrane. I use a staple gun…not a craft one but a more substantial DIY one. You might also want to cover the sides to create an enclosed space. If you’re putting against a house wall I suggest you google how best to back it.

Fill all areas with compost.

Choose your plants…depending on the size of your pallet and your gaps, you’re looking for 2/3 per slat space/area. Choose a range to suit you. I have three types of fern forwards the bottom, a few herbs in amongst, a few pretty little flowers, some sedums that grow tall, some that will trail, and some taller plants (erysimum, wallflowers) for the top to make it pretty!

Plant as usual where you fancy. Shady, water loving plants towards the base.

Water and wait until all soaked in.

Raise pallet, leave a gap of 2/3 inches between the base of the pallet and the wall and lean gently!

I would definitely suggest securing the top of the pallet to the wall. I was lucky, there were already several screws in the wall and the perfect height. I used garden wire, wrapped around a top slat, round the screw, onto the next screw and back around the top slat of the next pallet.

Stand back and admire your new garden!

DIY Pallet Garden #1
DIY Pallet Garden #1

B…
If you chose the lean up and plant when in place option, here’s what to do next…

If you’re putting it up against a house wall I suggest you google how best to back it. You’ll need something like a waterproof membrane to put over the back of the pallet to prevent damp. But please do look it up properly. I use a staple gun…not a craft one but a more substantial DIY one.

Raise pallet, leave a gap of 2/3 inches between the base of the pallet and the wall.

I would definitely suggest securing the top of the pallet to the wall. I was lucky, there were already several screws in the wall and the perfect height. I used garden wire, wrapped around a top slat, round the screw, onto the next screw and back around the top slat of the next pallet.

Now you need little pouches for the compost and plants to sit in. I was lucky…each half (left or right side) was just the right length to use the bottom of a bag for life! Flatten the plastic bag, run a pair of scissors along about 3/4 inches up (leave it taller if you’re not sure, you can always cut down to size when you’ve tried it out) to cut the bottoms pouch section off. This will then sit inside each section and you use your staple gun to secure in place. I began with one staple in the middle at the back, then each end, then secured over the front lip of the slat at each end. It takes a little while.

If you don’t want to use plastic, weed netting or similar will be fine but you need something the water will drown through.

Stab holes with a pair of scissors through the bottoms of all the plastic pouches.

Fill each little pouch with compost but leave them shallow enough to top up with plants.

Choose your plants…depending on the size of your pallet and your gaps, you’re looking for 2/3 per slat space/area. Choose a range to suit you. I have three types of fern forwards the bottom, a few herbs in amongst, a few pretty little flowers, some sedums that grow tall, some that will trail, and some taller plants (erysimum, wallflowers) for the top to make it pretty!

Plant as usual where you fancy. Shady, water loving plants towards the base.

Water.

Stand back and admire your new garden!

DIY Pallet Gsrden #2
DIY Pallet Garden #2

Hope that helps everyone. I sort of made it up as I went along. If I did it again, I

think I’d go for the complete fill with compost and then lean up approach rather than the shallow ‘beds’…thinking it through, it would mean each plant has lots of space and growing room. What I might do as they grow is top up each section

with compost so it goes to the ‘top’ of each slat. I may even, at some point, take them down and redo if I find the plants aren’t growing strongly. But bear in mind, they’ll be a lot heavier if completely filled. I’ve also seen people used them as shallow raised beds laying flat!

DIY Pallet Garden Side
DIY Pallet Garden Side

Why not have a go yourself? We would LOVE to see your creations in our Facebook group Yes Bebe Babble! It’s a fantastic, friendly community full of ideas and inspiration like this!

Please follow and like us:
error

Leave a Reply

Your email address will not be published. Required fields are marked *